Installing Kitchen Cabinets

Cabinet Installation - How to Install Kitchen Cabinets

The most difficult part of hanging wall cabinets is lifting them to the appropriate height and holding them in place. This makes installing wall cabinets a 2-person job. 1. Remove old cabinets; repair any holes in the walls. 2. Locate wall studs using the stud finder. Snap vertical chalk lines to indicate either stud centers or edges. Note: studs are spaced at regular intervals. Most common is 16-inches, although 24-inch intervals are sometimes used in newer houses. Once you locate one stud and determine the distance to the next, measure to locate others. Full Article »

How to Install Kitchen Cabinets | Video | Cabinets & Shelving

1 Mark cabinet layout lines onto the wall. 2 Locate wall studs using hammer and finishing nail. 3 Mark stud locations onto back of cabinet. 4 Drill four holes through back of cabinet, which correspond to the stud locations. 5 Set cabinet on cabinet jack, hold cabinet level, then fasten to wall studs with 2 -inch drywall screws and finishing washers. 6 Check to make sure cabinet is plumb. 7 Use jigsaw to cut vent-hood hole in cabinet that goes over the stove. 8 Clamp next cabinet to the first installed cabinet, then screw it to wall studs. 9 Fasten the two cabinets together with 1 1/4-inch screws. 10 Hold 6-foot level across face of cabinets; if necessary, add shims at wall to align cabinets. 11 Lay base cabinets on floor, facing up, and clamp together. 12 Fasten together base cabinets with 1 -inch pan-head screws. 13 Slip shims between cabinets to maintain uniform width. 14 Use hammer to snap off excess shims. 15 Set base cabinets in place and check height to countertop layout line; cut filler strip to match discrepancy. 16 Move base cabinets, set filler strip on floor. 17 Level filler strip, then screw to floor with 3-inch drywall screws. 18 Screw back of base cabinets to wall studs. Full Article »

How to Install Kitchen Cabinets - wikiHow

# Make your decision to replace the entire cabinets. If your existing cabinets fit your space well enough and you just want to freshen up the look of your kitchen, don't rule out refinishing or refacing. Both of these options are likely to be less costly than replacing the entire cabinets. * Refinishing is replacing just the finish, by sanding off or stripping the old, worn paint or varnish if necessary and applying a clean, new coat. * Refacing is replacing just the fronts of your cabinets, the doors and, if necessary, the fascias just behind them. The cabinet itself stays where it is. * You can also replace the cabinet hardware, (the hinges, handles, and drawer pulls) to give them a fresh look without tearing out the entire cabinets. * Many new, modular cabinet systems have particle board for their interior. If your old cabinets are solid wood and in good condition, consider keeping at least the interiors. Full Article »

Installing Kitchen Cabinets from Armstrong

Shut off all existing water, power and utility lines. Remove existing appliances (stove, oven, refrigeration, sink, and dishwasher). It is best to move these out of the kitchen for easier access to the work area while the remodeling is being done. Remove old cabinets and countertops. Remove any moldings from the walls where cabinets are to be installed. Some floors and walls have uneven (high or low) spots, which will affect the installation. It will be necessary to locate these uneven areas and shim or scribe cabinets in order to make the installation plumb, true and square. Use the following procedures to identify your uneven areas. Full Article »

	Common Mistakes When Installing a Kitchen Cabinet Even an experienced carpenter can make a mistake installing a kitchen cabinet. Do the kitchen cabinet installation yourself but give your cabinet the professional…
	Install a Pantry to Compliment Your Kitchen Cabinets Do you stuff the cereal on top of the microwave? Do you hide potatoes in with the pots? Have you ever left the olive oil out on the counter because that long…